Chemistries                 1300 887 735

Dummy Product for data sheet and tender text

Dummy Product for data sheet and tender text
Product #: FP360_DATASHEET
Unit Price Contact Hach

The Right Technology for the Right Price

Due to its unique combination of submersible probe design and UV fluorescence sensing technology, the FP 360 sc delivers the best technology to detect oil in water and is priced below competitive UV fluorescent instruments.

Minimal Maintenance

The FP 360 sc has no tubes, pumps, or valves that can foul or require constant maintenance interventions. Maintenance is limited to occasional wiping of the sensor's measurement window, calibration once every two years, and Xenon lamp replacement every four years.

Reduced Laboratory Testing

While laboratory testing is the ultimate method of measuring oil in water, it is a long and complex process that requires special equipment and trained lab personnel. The FP 360 sc provides a cost-effective, continuous online monitoring solution to maintain process control and avoid oil contamination with minimal laboratory testing.

High Sensitivity and Selectivity

The FP 360 sc can detect and measure polycyclic aromatic hydrocarbons (PAHs) from 1.2 ppb to up to 5000 ppb (µg/L). This is approximately equivalent to a concentration of mineral oil between 0.1 to 150 ppm (mg/L). Furthermore, the FP 360 sc method of detection makes it impervious to interferences by turbid water or natural organic and biological matter that impact online light scattering, UV absorbance, and VIS fluorescence instruments.

One to Eight Sensors

The Hach Digital Controller Family can receive data from up to eight Hach digital sensors, including oil-in-water, suspended solids, turbidity, pH/ORP, dissolved oxygen, conductivity, ammonium, phosphate, SAC, and nitrate in any combination.

There’s no complicated wiring or set up procedures with the Hach family of controllers. Just plug the sensor to any Hach digital controller and it’s ready to use because it’s “plug and play.”

What's included?

Oil-in-water probe, user manual

Specifications

Ambient Temperature: -5 - 45 °C
Cable Length: 10 m
Calibration: Factory calibrated with UV fluorescence standard or process calibration with results of a grab sample analysis.
Detector: UV photodiode with interference filter; Compensation of daylight and flashlamp intensity fluctuations
Dimensions: 68 x 306 mm (D x L; without connector and suspension pin)
Excitation: Wavelength 254 nm
Height: 12.5 " or 68 mm
(D x H; without connector and suspension pin)
Light source: Miniature xenon flashlamp with interference filter
Material: Housing: stainless steel 316Ti (1.4571) or titanium
Measurement method: UV fluorescence method for polycyclic aromatic hydrocarbons (PAH)
Mounting Configurations: Immersion, Inline, or Bypass
pH Value(s): ≥ 4
Pressure Range: Max. 30 bar (measurement probe)
Protection Class: IP68
Range: Low Range:
0 - 50 ppb (µg/L) and 0 - 500 ppb (µg/L) PAH**
0.1 - 1.5 ppm (mg/L) and 0.1 - 15 ppm (mg/L) oil**

High Range:
0 - 500 ppb (µg/L) and 0 - 5,000 ppb (µg/L) PAH**
0.1 - 15 ppm (mg/L) and 0.1 - 150 ppm (mg/L) oil**
Reproducibility: 2.5 % of measured value at constant temperature (PAH)
Response Time T90: 10 s
Sample Temperature: 1 - 40 °C
Sensor cleaning: No
Storage conditions: -40 - 60 °C
Wavelength: Measurement: 360 nm
Weight: Stainless steel: 2.8 kg
Titanium: 1.8 kg
What's included?: Oil-in-water probe, user manual